Table Top Epoxy Resin Superclear 1 Gallon | 128 oz Kit, Anti-Yellow Highest UV Impact Resistance, Food Grade Safe, Ultra Crystal Clear Gloss, Bubble Free, Bar & Surface Coat, Tumblers, Wood, DIY

I have had this epoxy in my garage for almost 5 years now. I used less than 1/4 of it for a project 4.5 years ago and figured I'd try it on another project this week. It still worked great. I can't believe it had been such a good buy.

I have purchased this product several times and I am 100% satisfied with it. It mixes well and is crystal clear. I use it to put down layers onto table tops and to cast resin pens. The table tops pour out nice and I spread it out with a foam paint brush. I only have to get the thickness close as the resin then self-levels. Once it's spread out I use a heat gun to pop any surface bubbles. I then go away for 5 to 10 minutes. I return to use the heat gun to pop any micro-bubbles that have formed. It's hard to see them, but if you look at the surface at a steep angle while passing the heat gun over the resin you can see them pop. I am only passing the heat gun over the resin at the speed you might use a paint brush. I am not trying to heat the resin, just pop the bubbles. Then it's time to wait. 24 hours it's ready for me to apply another layer. I put things like old maps on the table so I will do 3 or 4 layers of resin.With the pens, I mix the resin and split it up into 2 or 3 small cups. I then add special dyes and glitters to each and stir well. I then let the resin sit for 10 to 15 minutes so that when I pour them into the pen mold, the different colors swirl around each other but don't mix together too much.I also tried a Chinese resin and I was not happy with how reliably it mixed. Sometimes it took several days to get fully hard. I have always had 100% success with this American made product and I can always take it out of the mold 24 hours later. I highly recommend this product.

Crystal clear and amazing finish. The picture doesn’t do it justice. This table is 8’ x 42” and the one gallon kit covered it completely. After a previous pour that developed a few spots that didn’t cure and I had to sand it down to bare wood again. I can’t emphasize just how important thoroughly mixing the resin and the curing agent is.

Very Nice I would buy again.

Worked and cured well - watch a few project videos first, and you'll be pouring resin like a pro in no time.Very low VOC - can be used indoors without mask as a result, which is HUGE! Make sure your pouring surface and work area is at least 65 degrees F for best results... and keep a hand torch ready, as just a quick pass of the Bernzomatic open flame will remove troublesome and unsightly "bubbles" that form during the early curing phase (before the epoxy sets).Took the dyes flawlessly, I had light gray base with blue and moss green details for walls, snow white for the ceiling (it was a multi-color, multi layer, multi piece custom bath enclosure) - sorry for the blurry image. Project came out looking great, the edges sealed perfectly with silicone, custom fit shower enclosure is 100% waterproof.Beware "buggy" grades of plywood as pouring substrate:I used a construction-grade 1/2 plywood as my flat base - and though nothing of it, as a good strong substrate.But if you use plywood as a base, especially construction grade, be careful as many commercial grade plywoods can have small "bugs" living just below the surface! I was unaware of this, and when my first coat of epoxy went on, I had to spend several minutes and intervals during curing picking "bugs" (small, gnat-like critters) which migrated out from the sub-layers of the plywood. At first i though I had a hole in my window screen, but no, they were coming from inside the plywood, and migrating INTO my lovely epoxy resin!Honestly I have run into this issue before, when 1st-coat painting fresh plywood projects - so it was more of a distraction, and actually did not harm the wood, the piece, or the project. It was just annoying, picking gnats out of setting epoxy... had I used particle board or another substrate, I would not have had this issue, so "my bad" but no harm done.I will definitely purchase this epoxy again: And excellent product, handles and performs very well, easy to use and "master"... looking forward to my next epoxy project!

Lo compre y lo seguimos comprando por su calidad.

It worked perfect for me. Set faster than i expected it to! Was clear, hardly any bubbles. The few I had was easily removed with my heat gun. I have ordered more. Highly recommend.

BUYERS BEWARE! THIS PRODUCT IS HORRIBLE, WISH I COULD GIVE 0 STARTS!!! I WAS USING ON A GLITTER TUMBLER APPLICATION AND BOUGHT DUE TO THE DECENT REVIEWS. ONCE I RECEIVED I MIXED 15 ML OF PART A WITH 15 ML OF PART B AND SLOWLY STIRRED FOR 5 MINUTES TO ENSURE IT WAS THROUGHLY MIXED. I NOTICED IT LOOKED CLOUDY, BUT NOT HAVING USED THEIR PRODUCT BEFORE I STILL APPLIED TO MY TUMBLER, WHICH IS COMPLETELY CLOUDY. I THOUGHT MAYBE I HAD DONE SOMETHING WRONG ON MY PART, SO I MIXED ANOTHER BATCH OF EVEN AMOUNTS OF PART A & B AND COMBINED FOR 3 MINUTES FOLLOWING THE INSTRUCTIONS TO THE T, THIS BATCH WAS JUST AS CLOUDY IF NOT WORSE THAN THE 1ST BATCH. OUT OF FRUSTRATION STILL THINKING I DID SOMETHING WRONG I HAD MY ADULT SON MAKE A BATCH USING THE EQUAL PARTS, AND IT WAS STILL CLOUDY!! I REACHED OUT TO THE CUSTOMER SERVICE FOR THE COMPANY AND WAS MESSAGED BACK THE INSTRUCTIONS ON MIXING AT WHICH TIME I RESPONDED THE 90 ML (IN 3 DIFFERENT BATCHES) WERE ALL MIXED CORRECTLY. THEY THEN MESSAGED BACK AGAIN ASSERTING I HAD NOT FOLLOWED THE INSTRUCTIONS. I ASKED TO RETURN THE PRODUCT AND RECEIVE A REFUND AT WHICH TIME I WAS INFORMED I COULD DO NEITHER BECAUSE THE PRODUCT IS OPEN AND USED. I HAVE LITERALLY USED 90 ML OUT OF 3785 ML AND THEY'RE REFUSING ANY ASSISTANCE OTHER THAN CONTINUING TO DISCUSS WITH THEM ON HOW I DIDN'T MIX THE PRODUCT PROPERLY. I'M THROWING THIS AWAY AND STICKING TO ANOTHER EPOXY THAT I KNOW WILL NOT CLOUD ON ME. THIS WAS A TOTAL WASTE OF OVER $60!!!!