3 Way Speaker Crossover, PUV-W3 200W Passive Crossover for HiFi Home Audio 4 to 8 Ohm Bass Mediant Tweeter Bookshelf Speakers - 2Pack

I’m using a car audio amplifier for some Dayton audio speakers and the crossover on the amplifier wasn’t giving enough of a full sound for me, (setting high and low pass to 90hz as recommended). These sound fantastic and make the speakers blend fantastically. I do not recommend using a subwoofer with the bass output on this crossover use the 90hz lpf instead because it does not block out the middle-low midrange on the bass output. Instead I recommend using a larger PA midbass-midrange style woofer such as a 8 inch like mine or even a 10 in a 4way set up like mine. A 6.5 would work but I’m not sure it would have as much of the lower midbass range as you larger woofers. Also it says 4-8 ohm but I have one crossover on a bridged channel to my mids and tweets to a final impedance of 2 ohms ( 4-8ohm svc speakers, +and- all wired together on each drivers), so you’ll be safe as long as you don’t drastically exceed the 200 watt rms rating. I’m going to make another speaker as shown in my picture and use it in a dj set up it gets loud and very crispy clear. I can’t record and play Bluetooth at the same time otherwise I’d record a video but I highly reccomend them for a similar to mine setup. The subwoofer is a 10 inch infinity kappa car subwoofer in a 1.5 cube 32 hz tuned birch 4 inch circle ground firing-ported box that works great in home audio or car audio applications as well.

These crossovers were just what I needed for the 3way speakers of my homemade DIY boombox project. Easy to install. Screw terminals make it easy to connect. Speakers sound great!

I have no idea what these are meant to go to, but I put them in a set of KLH 9912s with damaged crossovers. They cost $6 each and they work. They appear fairly well made and the crossover ranges are fairly appropriate. Zero complaints for garage speakers.

Connections are labeled, easy, and also removable! I restored some older speakers which sounded dull. With these, the mid-range and hi-range drivers really open up, and provided amazing clarity.The bass output does seem to have a hard cutoff at around 45Hz, so the I felt it was lacking for my speakers, which have 12" drivers. I decided to straight-wire the woofers, bypassing the crossover (which was how they were originally wired, using the woofer's natural roll-off) and the bass response was better. The mids and highs still run through the crossover, and are still crystal clear, so I'm still very happy with this crossover. If the bass had a lower limit of say 20Hz, these would be perfect.Still, for the price, this is hard to beat!

I rebuilt my Fisher 12" 3-way cabinets Replacing the tweeters and mids. I kept the heavy double magnet 12" woofers.Used 6" full range and 3" tweeters. These crossovers replace the originals.WOW man, what a difference. Thumping away (:If you are doing a re-build and/or replacing a couple speakers in Your Vintage 3-way cabinets, try these, for the low cost they are the "Bomb"You will hear instruments in songs that you did not know were even there !I can't believe the sound quality.

I used this in a bass guitar amp, hoping to separate the mids from the lows, since the amp itself is uniquely configured, with a single 15" and two 8" speakers. This crossover didn't feed anything at all via the middle channel, so I've removed it. I have tried several similar units, with equally unsatisfactory results. I'm tired of returning them. Also, the bass response produced distortion, so it didn't do that part well either.

Worked excellent. Would definitely use again. Made my older sony tower speakers sound so much better. Bass is no longer musdy and midrange is much better along with the tweeters. Hearing crisper clearer sounds I didn't hear before. Thanks.

Matched well with my vintage BIC Venturi V630's.It's a simple crossover, but has all the wiring hardwired to the crossover. Impressed for that price.