Quick Click Dust Collection Separator

Awesome product. Great quality, I was expecting cheap plastic but this product is great. I've used it for drywall sanding dust collection. If you have lung problems such as asthma or COPD this product is a life saver.

Highly impressed with this cyclone dust separator. Tested it on a rather large amount of saw dust that was on the shop floor, it have it attached atop a 22 gallon plastic drum and then to an 8 gallon 4.5 HP shop vac brand vacuum. I'd say 99.9% of the saw dust is in the plastic drum. Unbelievable. Highly recommend this one.

This Dust Collection Separator works great with a solid metal container or plastic container with supported walls. The plastic container walls collapsed inward due to the sucking power of the wet vac.

The media could not be loaded. I ended up attaching this to my smaller shop vac for the laser engraving area since my system is in the shed and get very dusty and leaves get in with all the trees around.The setup is very easy and used a reinforced cover on a 30 gallon HDPE drum that's also easy to take off with the plastic ring. It ended up bigger than I liked but also wanted minimal duct length. I used an elongated 90 degree PVC pipe to make sure I'm not losing a ton of CFM.It's working well so far and the suction hasn't slowed down. While the shop vac has it's own filter, it's hardly dirty and keeping it nice and clean. The filter at least filters out any fine dust and particles which I've seen a huge difference.The unit is also very well made and seems durable.I almost didn't catch this product and maybe the way the product photo was shot so something the vendor can keep in mind and perhaps, more visuals for the actual product being used. But, I'm glad I found this product!

We are using it as part of a DIY jewelers dust collection system. I like the squat height on the unit. Helps it fit beneath the bench. I've had a different brand I've used in my workshop for actual woodworking that did work well but that would be too tall for where I planned to put this guy.Using this with a 220CFM inline fan that dumps into a large 1 micron exhaust bag. Running through about 6 feet of tubing to a fishmouth station. Enough power and cyclone action to suck in grinding and sanding debris from a couple inches away and see the precious metal drop out of the airstream once it hits the cyclone portion.If you're going this route I think 220CFM fan is good enough for one close station. I was actually trying to power two stations at once and with both blast gates open on a Y split. The closest station gets good flow but less so on the second fishmouth about 10 feet away from the fan in total. We will be bumping the inline to a larger 6inch 400CFM unit that should overcome that issue.

I ordered this product for use on my Blast Cabinet. Like most of the post on Blast Cabinets finding, adapters to go from the various vacuum hoses and connections is a major issue. I contacted Cen-Tec about my issues. They requested additional information and immediately provided assistance to resolve my issues. Not only do they make an outstanding product, their support is outstanding as well. I highly recommend Cen-Tec products

The Quick Click Dust Collection Separator has been working great for the month since I put it into service. Other DIY cyclonic dust separator builders have had issues attempting to use 15-16 gallon plastic buckets as a dust receptacle because they collapsed under vacuum. I went with a 16 gallons VEVOR Fryer Grease Bucket (also available on Amazon). This strong metal bucket does not have that problem. It provides an ample volume for dust and has a very good soft rubber seal with clips holding the lid down. The included mobile base makes it easy to move the separator around the shop. A 4" hole saw provided a perfectly sized hole in the cover to mount the Quick Click Dust Separator. The 4 machine screws and rubber seal provided with the separator mount it to the bucket and provides an excellent seal. I like the option to connect 2-1/4" shop vac hoses or 2-1/2" hoses. The overall construction seem better than other plastic separators. I'd buy is again.

Keeps the sawdust in one place. Good investment without spending a $100 buck to get the job done.