3D Printer Enclosure for Bambu Lab A1 Mini, Clear Acrylic Bambu A1 Mini Printer Dust Cover with LED Light,Dustproof Tent Constant Temperature Protective Cover Box(470×470×470mm)

Solid build. I read a lot of reviews complaining about the acrylic plates rattling, but I can barely hear it. There are shims on MakerWorld (just search for Yoopai and you’ll find everything).The A1 Mini is not designed for ABS, so keep that in mind if that’s why you’re buying this. The enclosure and the printer will both require modifications.The LED is plenty bright.Assembly wasn’t the quickest thing, but it wasn’t particularly difficult. Just make sure you pay attention to orientation; I had to start over halfway through because I put one of the sides together backward (entirely my fault).It fits the print nicely. I would not recommend using this enclosure for anything larger than the A1 Mini tho. I tried to put my Ender 3 V2 in it and it was slightly too tall.Overall a nice product for the price.

This is a great enclosure that I would definitely buy again. I gave 4 stars due to my suggestions for improvement. It does have some cons, but I’ll start with the pros.1. Looks great2. Materials seem to be high quality3. It’s an enclosure…there’s not really much to get wrong here.4. Extra screws and such includedCons1. Assembly is quite difficult. Definitely set aside an hour or two to put this together.2. It does rattle a bitSuggestions1. I would like to see a bottom piece included with this. Even if it’s another “hollow board” or just something cheap that isn’t necessarily another sheet of acrylic.2. I think it would be nice to be able to switch to Fahrenheit on the thermometer.3. I believe some small pieces of foam to insert in the frame would go quite far in terms of the rattle from the acrylic sheets.4. I think at this price point the 3 additional pieces to mount the AMS system should be included and not something you have to print separately.

The directions for putting the enclosure together were worthless. The parts have to be assembled in a specific orderor they won't go together. The reason is the panels cut notches have to be installed in the beam members in an exact order. I had problems with the door hinges.I had one door where the hinge pin was screwed on and broke into four pieces. I could only find three of them. There was no way I could fix the door. Then I had the second door crack at the hinge pin. I was able to superglue it to hold the door in place. I reached out to the seller who responded they needed a picture. I am 78 years old and can't give them a picture. I can't believe they would think I just wanted an extra door.The enclosure is put together except for the broken door. The sides are very loose in the framing members. The enclosure will not stop the noise but it will amplify it. I will need to add shine all around to tighten the sides to the framing members.The seller has declined to help me with the broken door. They are not going to send me a new door as requested.I would not recommend you to purchase it! You can get a soft shell enclosure that would dampen the noise and keep the heat in the enclosure. This alternative is much cheaper.After reading all the reviews I found that many of the reviews complained about how poorly they were written. I found several individuals that had the doors break at the hinge point. All the panels set loose in the framing members require shims to be installed. The seller did not include any shims. The seller did not respond to the poor reviews and what the buyers could do about it.I would like Amazon to remove this seller from their website. The seller clearly knows the product is poorly designed. Also, the seller has no intention to address buyers' issues with part replacement.

Directions not well written but can be figured outDoesn't fit up niecely, the printed parts have suppert material still on them blocking pathways for yubesIt does fit an A1 mini but your placement is imortant, it needs to be just right.Flimsy and doesn't line up great, the side panels are not sturdy (should have been thicker) the one that holds the single spool very noisy.Doors do NOT line up no matter how hard you tryProbably will not mount the AMS on top, it looks great but due to the flimsy nature this is a concern.if you need a very basic enclosure this will fit the bill but you cn do better

I bought this to enclose my Bambu A1 Mini and I couldn't be happier.. ofcourse after a few adjustments. Although it isn't perfect but it meets what it is used for.Notes to those who wants to use it:1. If possible position the AMS lite top solution closer to the edge so that you can trim or cut the PTFE tube to avoid issues with filament loading.2. Have a little insertion on top of the right side of the beam since it makes a sound as it calibrates. This could be because the ptfe tubes connects to the side pannel through the pneumatic connector.3. If you can, print a round rack or filament holder since resistance is greater with this included rack not to mention that it makes a sound everytime filament is being pulled.4. I wish the Yoopai maker made the whole for the ams lite wire closer to the edge so that it's not an eye sore but can be acceptable.5. Lastly, I open the door from time to time since it gets really warm and I still don't have an exhaust.. 😀But overall, I am very pleased.

I absolutely ❤️ this enclosure exactly what I was looking for a clear enclosure that I can see clearly from front view and sides. Helps keep sound down also helps to keep your printer collecting dust. Great lighting. I would buy this again as well as recommend it to a friend.Update… still enjoying my enclosure I’ve since added a magnetic strip to the inside of the door then I put a another strip on the outside center of door to keep the door sealed and flush works great. Did another update changed the light with a led color changing light pics added