2025 Official Space Pi Filament Dryer Plus, 2 Rolls 3D Printer Filament Dry Box with 360° PTC Fast Heating, 4'' LCD Touch Screen, Filament dehydrator Fits 1.75/2.85mm PLA PETG ABS Filament

I really like this dual spool filament dryer! Not only does it have twelve different pre-set filament types, but all the settings are adjustable. It has two heaters and two fans so it evenly distributes the warm dry air completely around my filament spools which drops the humidity level inside quickly and evenly. The filament rolls easily load in from the back, and they sit on two shafts with bearings to allow filament to be easily be pulled into the printers. The best part is I can pull filament directly from the dryer to two printers at the same time. This is now my favorite filament dryer.

This dryer is great. My only gripe is that the ptfe tubing attaches at the front so filament has to be loaded around it. I feel that they could have designed it so that it was attached in the rear with opening towards the front to make loading easier.With that said it works great. I have a different brand that has hot spots and if there are two filaments loaded and one not being used or either being used in the printer while dryer is on it does somewhat melt the bottom side of the filament fusing it together slightly. However I have not had that issue with the Creality one.

I have 3 of these feeding my Prusa XL and MK3S. Easy to use and feed from.

Makes an odd noise. Sounds like the motor is scrubbing from time to time. If I give it good whack, it starts to behave and runs quietly.

This is my second filament dryer. The first was another brand. It only went to 50 degC, so it went back to Amazon.This dryer does an excellent job of drying filament. It's easy to use for that purpose.I wish feeding filament from the dryer were as easy. Some filament is sensitive enough to moisture that it's easier to keep it in the dryer. To do this you need filament holes that allow the filament to flow easily to your printer. This dryer has those holes, but their on the top of the box. This means they have to wind around to get to your printer. This adds to the friction and makes using it difficult.

I am so glad I purchased this great dryer. I do a lot of duel and multicolored printing.This dryer has made that process so much easier. Even if I am printing a single color, I can have the filament for the next print drying. You are able to feed two printers at one time while printing from the dryer. It comes with two PTFE tubes to feed the dryers. The dryer has two ports that feed out of the top of the dryer. The part that really impressed me was how fast it heats. I timed it from start to 70C. It took 4 minutes 42 seconds. That is by far way faster than any other dryers I own. I used my meter to test the temperature to see if it matched the display. (see picture). As you will see, it's very accurate. I moved the thermistor around to check and see if it was an even temperature throughout the box. The fans circulate the heat very well. The temperature was even everywhere in the dryer box. The fans are strong and move a lot of air, but they are quiet. You can set the timer from 0 - 48 hours. The display is very bright and responsive. The display has 12 presets for different kinds of filaments. So it will set the proper temperature for you and take the guessing out of it. You can also set it to any temperature you like manually from 45C to 70C. You can change the readout from Celsius to Fahrenheit if you prefer. The display has a humidity monitor. If you have poor adhesion, clogging, or bubbles, this dryer will solve those problems and more. It has two storage departments that hold desiccant packs at the bottom of the dryer. That is great if you want to store your filament and keep it dry a day or two before printing. I highly recommend this dryer, especially over any single dryer.

Fantastic job drying filament, used on old TPU and dried it out perfectly. Easily feeds from unit directly to printer.

Ok. The dryer looks fairly nice, and the interface is very simple, if prone to fingerprint smudges. Well packaged and doesn't feel like really cheap junk. but..So the product is for sure overheating my filament. I bought this a few months ago. Perhaps 60-70 days ago and have used it maybe 10 times.(for 4-5 hours per run) Recent attempts have cooked the product and even more so the spools. The spools are Pet-G, yes I'm sure. They have survived a few dozen go rounds in my old Sunlu dryer, which I already gave away to my son in law when I bought this due to wanting a double unit. This dryer has also cooked a bambu spool almost as bad as the above image and they are for sure supposed to be high heat resilient. I have to say at this point, I may try to use it on its lowest temp setting which I believe is PLA and hope it won't cook my filament to a crisp again. The roll in the image above is so brittle its pretty much unusable as it will break off in my hand or in the AMS. I would recommend you avoid this based on admittedly very small sample size. Also the screen intermittently goes all wonky as if it is shattered, which I was unable to get a picture of for this review as it is inconsistent. Also like every third or forth time I used it, the fan would wail a terrible mechanical screaming that I would need to stop the machine, shake it vigorously and try again to get rid of. (some fan issue) It was too expensive in my opinion to justify all these combined issues, and it ruining filament is simply not ok.Consider yourself fairly warned.