DOME GLASS Whitestone GEN Film Screen Protector for Samsung Galaxy Z Fold 3 (2021) Anti-Bubble HD Clear Hard Coated PET Film Screen Guard

Honestly the screen protector is really good. It feels better than the original screen protector and was fairly simple to install. My only complaint is that the instructions really exaggerate how simple removing the original screen protector cab be. The way it sits under the frame can be really difficult to get to and I could see how it could be easy to damage the inner screen itself during removal. Also the screen protector leaves behind a severe amount of residue. The single alcohol pad that was included in the kit was not nearly enough to remove all the remaining adhesive on the screen. So if you are going to install this yourself buy a high quality microfiber cloth, compressed air, and a flashlight. To remove the inner screen protector I would recommend starting from the middle using a plastic pry tool or a guitar pick if you have. You have to gently pry up til you see a bubble forming. Once you see that bubble forming make sure to turn on the screen to ensure you aren't below the oled screen. Once you confirm you are above the oled work back and forth from left to right to expand the bubble. One you can grab gently start to peel it away while using your free hand to hold the phone in place. Once fully removed use some rubbing alcohol (preferably 90% or higher) and the included micro fiber cloth to remove the old adhesive. Then use your personal micro fiber cloth to clean the screen. Use a flash light directly above the screen while sitting away to ensure dust does not fall onto the screen. Use the compressed air to blow off all the dust and particles and use the included dust remover to get rid of any hard to remove pieces of dust. After ensuing it's fully clear follow the remaining instructions in the video to apply the screen. Make sure to follow it exactly as they do. Including putting pressure on each side while removing the mounting holes. After removing the outer plastic make sure to use the smaller side of the spudger to push out any remaining air bubbles. Then make sure to let it sit open for 15 min for the adhesive to fully stick. Then fold and open your phone a few times to ensure no bubbles have formed. If following these steps exactly you should have a perfectly seated screen protector with no bubbles or dust. I'll attach a photo of mine later to show how I will look when done properly.

If I could review it and not give any stars or there would be a minus infinite option to describe it i would give it... By far this is the worst product I have bought on Amazon, in my many yrs purchasing. Horrible!! It's been 2 weeks and it has this bubble line from folding the phone and a lot of bubbles!! Will have to get a new one... and it only comes with one... I have bought other types much cheaper , that last long, long time ... had to buy this one because because got a replacement phone, and this one looked thicker... stupid choice!!!

The OEM inner screen protector for my Z Fold 3 started to peel at the center so I figured it was finally time to try replacing it. Samsung doesn't seem to sell their OEM protectors anywhere unfortunately so Whitestone was the next best thing. I didn't have high hopes since the OEM protector feels so nice and is always installed perfectly and bubble-free (I mean I would hope so for a factory installed protector). And installing dry films just involve lining up the film and praying the bubbles squeegee away right? Not with Whitestone.Out of the box, you get 1 inner screen protector, a standard cleaning kit (microfiber, alcohol wipe, and dust remover), a crazy looking jig, and equally crazy looking squeegee, a screen remover, and an anti-slip pad. This is the part where you stop touching the pieces and open the guide video using the QR code on the back of the box. Seriously. Don't waste your time trying to figure it out, messing up, putting up a 1 star review, and invalidating the developers' hard work. These guys don't mess around. The video instructions are in Korean, but just follow along with what the person is doing and you'll be ok.After installation, I just found a few bubbles on the very edge of the screen that I gently pushed out, no problem. But other than that, it looks and feels OEM. It's actually incredible how much a little creative engineering can eliminate the problem of bubbles stuck in the middle of your screen. And with a Z Fold 3, you have a long way to go to push those bubbles out. For $20, this is a steal. If your OEM protector is starting to peel like mine (I bought mine on release day so it's been around 11 months), just get this. Super easy, and it'll make your phone look and feel brand new again.