Wasserstein 30° to 55° Horizontal Wedge Wall Mount Compatible with Eufy Security Video Doorbell Wired Version & Eufy Security Video Doorbell Battery Version

Product is great for replacing in wall (side facing) original doorbell mounted on the side of the the door with an extended view. Please note viewing angle was good but not sufficient, so I also used Eufy’s included 15* wedge on top.Manufacturer should include longer screws to mounts for attaching doorbell to the wedge (not included). Luckily I found two screws a little short of an inch length at home in my tool box to mount doorbell plate including Eufy’s original wedge to this products wedge for installation.End result is satisfactory. Product is not bulky and smaller than the doorbell. Time will tell how it holds up in the long run with this wedge. But for now I am well happy that I saved $180 quote for professional installation by an electrician compared to this $15 approx product DIY.I do recommend it overall as it’s a great buy. Please know patience is the key here as it took me some time to figure it out but was worth it.Good luck 👍

We needed a 45 degree angle for the doorbell to fully show the porch and this is the only product I can find to increase the angle. The angle locking screws are a bit harder to install because I didn't have any magnetic screw drivers but the whole installation took <30 minutes. I'm super happy with this mount and my Eufy 340 doorbell.

We have a double door on the front of our home, so the doorframe (and doorbell) are next to a side wall. This product provides a better angle for the doorbell camera so as to be useful.Although the instructions printed on the box were basically useless (the font size was way too small for these old tired eyes), the small diagrams were enough to get the idea across.The most difficult part of the installation process (for me) was the insertion of the small screws to determine the desired angle for the doorbell. That bottom screw took a bit of time to insert. Like I said earlier, the eyes are a bit weary. As for the rest of the installation, it all went pretty smoothly - probably took about 20 minutes from my day.The included hardware worked well, and the materials used in the product are sufficient for the task at hand. For much less than twenty dollars this product does a great job making the doorbell installation a bit more flexible.All in all, I would recommend this product for anyone needing to increase the angle of their Eufy doorbell. I rate it 4 stars only for the insanely small instructions on the box. The manufacturer could do better in this department - not every customer has the eyes of an eagle...

Why advertise it fitting both wired and battery versions if it doesn't? The holes are not even CLOSE for the battery version. OK, wrote this review 3 hours ago, and just decided to hack the crap out of it to get it to fit. gound the nubs off the back of the eufy snap mount to make it fit flush, then drilled 2 new holes in it to match the ":Wassershite" bracket to fit the parts together. Hey, ya know, most of thw pother reviewers are right - this bracket is total garbage. An IDIOT designed this. WORST assembly setup ever. who designs something to be assembled "after installation"? Just wait until you enjoy trying to get the tiny screws into the top and bottom of the bracket AFTER it's mounted on your surface. Stupidest design ever. VERY FLIMSY also. Looks like I will have the design my own and fire up the 3D printer. Just had hoped that his part wasn't going to be junk - Boy, am I wrong!2/18/22 update: After just over 7 months, the part has warped to the point that the camera unit can no longer be popped in. I just wish that there were other options.

My doorbell is located on the inner wall of my door jamb and the 15 degree base that’s included with the Eufy s330 still shows a large part of the door.This solution is adjustable and that’s both great and a concern. Then again, in my situation I needed the maximum angle (55) and a fixed base would be much more sturdy.Installation is straight forward, but with a few challenges from small screws and a snap hinge that’s not very effective. Also, the pass through is fairly small to barely accept the wire nuts. All that makes this a bit more challenging than it needs to be.You install the bottom part first, then snap in the top part and insert the (very small) screws to fixate the angle. The screw on the bottom can be a challenge without a sufficiently magnetic screwdriver.The real challenge for me was to attach the base plate that comes with the camera. There are two bolt patterns and the inner set fits the Eufy S330 plate just fine, but the screws are tiny. That’s less of a handling concern, but the flat heat is only minimally supported by the countersunk holes. I had to add a washer and it still doesn’t feel very secure.The base holds the camera in a much better position, and with $14 it’s reasonably priced, but this will not ease concerns if you’re worried about someone stealing the camera. Also, the small screws and overall “flimsy” design is a bit of a negative.

I started with one of these to try them out.I have no added one at all my doors. Also recently purchased camera. Great support and easy to use. Good quality

It tilts the Eufy Wired Doorbell at just the right angle so I can observe activity at my front door without losing sight of any visitors. Good thing as I lost the original mount for my doorbell.

Just received this today May 3, 2023. Install was super easy and it works fantastic for my need. I have the newer model Eufy dual camera doorbell and it fits perfectly fine as it has 2 sets of holes for the screws to mount the doorbell base.

Bought this for my Aosu doorbell cam. Way to small. So gave it to brother in law for his Eufy doorbell and it's worked amazing. But I still say my Aosu is a better doorbell Cam 😉

De wandhouder is stevig genoeg om de deurbel te bevestigingen.Is er een minpuntje? Ja, de deurbel heeft een paar nokjes aan de achterkant.Het zou mooi zijn geweest als deze in de wandhouder zouden hebben gepast.Nu is er een spleet tussen wandhouder en deurbel. Ik heb dit opgelost door de meegeleverde 15' graden wandhouder er tussen te monteren. Dit maakte in ons geval niet uit.

Did what it says on the tin. Works spot on easy to adjust and simple to fit without instructions! Awesome. Would recommend!

Good product and very easy to fit with the Eufy doorbell. Enabled my to get the bell at just the right angle to view people approaching the door from 2 directions. May appear a bit flimsy on its own but is strong enough when fitted to the doorbell.

Work for me